 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MOTOROLA SEMICONDUCTOR TECHNICAL DATA Order this document by MRF9030M/D The RF Sub-Micron MOSFET Line RF Power Field Effect Transistors N-Channel Enhancement-Mode Lateral MOSFETs Designed for broadband commercial and industrial applications with frequencies up to 1.0 GHz. The high gain and broadband performance of these devices make them ideal for large-signal, common-source amplifier applications in 26 volt base station equipment. * Typical Performance at 945 MHz, 26 Volts Output Power -- 30 Watts PEP Power Gain -- 20 dB Efficiency -- 41% (Two Tones) IMD -- -31 dBc * Integrated ESD Protection * Capable of Handling 5:1 VSWR, @ 26 Vdc, 945 MHz, 30 Watts (CW) Output Power * Excellent Thermal Stability * Characterized with Series Equivalent Large-Signal Impedance Parameters * Moisture Sensitivity Level 3 * Dual-Lead Boltdown Plastic Package Can Also Be Used As Surface Mount. * TO-272 Available in Tape and Reel. R1 Suffix = 500 Units per 44 mm, 13 inch Reel. * TO-270 Available in Tape and Reel. R1 Suffix = 500 Units per 24 mm, 13 inch Reel. MRF9030MR1 MRF9030MBR1 945 MHz, 30 W, 26 V LATERAL N-CHANNEL BROADBAND RF POWER MOSFETs CASE 1265-07, STYLE 1 (TO-270) PLASTIC (MRF9030MR1) CASE 1337-01, STYLE 1 (TO-272 DUAL LEAD) PLASTIC (MRF9030MBR1) MAXIMUM RATINGS Rating Drain-Source Voltage Gate-Source Voltage Total Device Dissipation @ TC = 25C Derate above 25C Storage Temperature Range Operating Junction Temperature Symbol VDSS VGS PD Tstg TJ Value 65 +15, -0.5 139 0.93 -65 to +150 175 Unit Vdc Vdc Watts W/C C C ESD PROTECTION CHARACTERISTICS Test Conditions Human Body Model Machine Model Charge Device Model MRF9030MR1 MRF9030MBR1 Class 1 (Minimum) M2 (Minimum) C7 (Minimum) C6 (Minimum) THERMAL CHARACTERISTICS Characteristic Thermal Resistance, Junction to Case Symbol RJC Max 1.08 Unit C/W NOTE - CAUTION - MOS devices are susceptible to damage from electrostatic charge. Reasonable precautions in handling and packaging MOS devices should be observed. REV 3 MOTOROLA RF Motorola, Inc. 2002 DEVICE DATA MRF9030MR1 MRF9030MBR1 1 ELECTRICAL CHARACTERISTICS (TC = 25C unless otherwise noted) Characteristic Symbol Min Typ Max Unit OFF CHARACTERISTICS Zero Gate Voltage Drain Leakage Current (VDS = 65 Vdc, VGS = 0 Vdc) Zero Gate Voltage Drain Leakage Current (VDS = 26 Vdc, VGS = 0 Vdc) Gate-Source Leakage Current (VGS = 5 Vdc, VDS = 0 Vdc) IDSS IDSS IGSS -- -- -- -- -- -- 10 1 1 Adc Adc Adc ON CHARACTERISTICS Gate Threshold Voltage (VDS = 10 Vdc, ID = 100 Adc) Gate Quiescent Voltage (VDS = 26 Vdc, ID = 250 mAdc) Drain-Source On-Voltage (VGS = 10 Vdc, ID = 0.7 Adc) Forward Transconductance (VDS = 10 Vdc, ID = 2 Adc) VGS(th) VGS(Q) VDS(on) gfs 2 3 -- -- 2.9 3.8 0.23 2.7 4 5 0.4 -- Vdc Vdc Vdc S DYNAMIC CHARACTERISTICS Input Capacitance (VDS = 26 Vdc 30 mV(rms)ac @ 1 MHz, VGS = 0 Vdc) Output Capacitance (VDS = 26 Vdc 30 mV(rms)ac @ 1 MHz, VGS = 0 Vdc) Reverse Transfer Capacitance (VDS = 26 Vdc 30 mV(rms)ac @ 1 MHz, VGS = 0 Vdc) Ciss Coss Crss -- -- -- 49 27 1.2 -- -- -- pF pF pF FUNCTIONAL TESTS (In Motorola Test Fixture) Two-Tone Common-Source Amplifier Power Gain (VDD = 26 Vdc, Pout = 30 W PEP, IDQ = 250 mA, f1 = 945.0 MHz, f2 = 945.1 MHz) Two-Tone Drain Efficiency (VDD = 26 Vdc, Pout = 30 W PEP, IDQ = 250 mA, f1 = 945.0 MHz, f2 = 945.1 MHz) 3rd Order Intermodulation Distortion (VDD = 26 Vdc, Pout = 30 W PEP, IDQ = 250 mA, f1 = 945.0 MHz, f2 = 945.1 MHz) Input Return Loss (VDD = 26 Vdc, Pout = 30 W PEP, IDQ = 250 mA, f1 = 945.0 MHz, f2 = 945.1 MHz) Two-Tone Common-Source Amplifier Power Gain (VDD = 26 Vdc, Pout = 30 W PEP, IDQ = 250 mA, f1 = 930.0 MHz, f2 = 930.1 MHz and f1 = 960.0 MHz, f2 = 960.1 MHz) Two-Tone Drain Efficiency (VDD = 26 Vdc, Pout = 30 W PEP, IDQ = 250 mA, f1 = 930.0 MHz, f2 = 930.1 MHz and f1 = 960.0 MHz, f2 = 960.1 MHz) 3rd Order Intermodulation Distortion (VDD = 26 Vdc, Pout = 30 W PEP, IDQ = 250 mA, f1 = 930.0 MHz, f2 = 930.1 MHz and f1 = 960.0 MHz, f2 = 960.1 MHz) Input Return Loss (VDD = 26 Vdc, Pout = 30 W PEP, IDQ = 250 mA, f1 = 930.0 MHz, f2 = 930.1 MHz and f1 = 960.0 MHz, f2 = 960.1 MHz) Gps 18 20 -- dB 37 41 -- % IMD -- -31 -28 dBc IRL -- -13 -9 dB Gps -- 20 -- dB -- 40.5 -- % IMD -- -31 -- dBc IRL -- -12 -- dB MRF9030MR1 MRF9030MBR1 2 MOTOROLA RF DEVICE DATA VGG + C8 B1 B2 VDD + C7 L1 L2 C15 C16 + C17 + C18 RF INPUT C5 Z1 C1 C2 C3 C4 C6 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9 Z10 DUT Z11 C9 Z12 Z13 Z14 Z15 Z16 Z17 C14 C10 C11 C12 C13 Z18 RF OUTPUT Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9 Z10 0.260 x 0.060 Microstrip 0.240 x 0.060 Microstrip 0.500 x 0.100 Microstrip 0.200 x 0.270 Microstrip 0.330 x 0.270 Microstrip 0.140 x 0.270 x 0.520, Taper 0.040 x 0.520 Microstrip 0.090 x 0.520 Microstrip 0.370 x 0.520 Microstrip (MRF9030MR1) 0.290 x 0.520 Microstrip (MRF9030MBR1) 0.130 x 0.520 Microstrip (MRF9030MR1) 0.210 x 0.520 Microstrip (MRF9030MBR1) Z11 Z12 Z13 Z14 Z15 Z16 Z17 Z18 Board 0.360 x 0.270 Microstrip 0.050 x 0.270 Microstrip 0.110 x 0.060 Microstrip 0.220 x 0.060 Microstrip 0.100 x 0.060 Microstrip 0.870 x 0.060 Microstrip 0.240 x 0.060 Microstrip 0.340 x 0.060 Microstrip Taconic RF-35-0300, r = 3.5 Figure 1. 930-960 MHz Broadband Test Circuit Schematic Table 1. 930 - 960 MHz Broadband Test Circuit Component Designations and Values Part B1 B2 C1, C7, C14, C15 C2 C3, C11 C4, C12 C5, C6 C8, C16, C17 C9, C10 C13 C18 L1, L2 WB1, WB2 PCB Description Short Ferrite Bead, Surface Mount Long Ferrite Bead, Surface Mount 47 pF Chip Capacitors, B Case 0.6-4.5 Variable Capacitor, Gigatrim 3.9 pF Chip Capacitors, B Case 0.8-8.0 Variable Capacitors, Gigatrim 6.8 pF Chip Capacitors, B Case 10 F, 35 V Tantulum Chip Capacitors 10 pF Chip Capacitors, B Case 1.8 pF Chip Capacitor, B Case (MRF9030MR1) 0.6-4.5 Variable Capacitor, Gigatrim (MRF9030MBR1) 220 F Electrolytic Chip Capacitor 12.5 nH Coilcraft Inductors 20 mil Brass Shim (0.250 x 0.250) Etched Circuit Board Value, P/N or DWG 95F786 95F787 100B470JP 500X 44F3360 100B3R6BP 500X 44F3360 100B7R5JP 500X 93F2975 100B100JP 500X 100B1R8BP 44F3360 14F185 A04T-5 RF-Design Lab 900 MHz 250/Viper Rev 02 Manufacturer Newark Newark ATC Newark ATC Newark ATC Newark ATC ATC Newark Newark Coilcraft RF-Design Lab DSelectronics MOTOROLA RF DEVICE DATA MRF9030MR1 MRF9030MBR1 3 C18 B2 VDD C8 C15 L1 C1 C2 C3 C6 WB1 CUT OUT AREA C4 C5 WB2 C10 C9 L2 C14 C11 C12 C13 C16 C17 C7 VGG B1 MRF9030M Figure 2. 930-960 MHz Broadband Test Circuit Component Layout (MRF9030MR1) C18 C8 VGG B1 C7 C15 B2 C16 C17 VDD C1 C2 L1 C5 CUT OUT AREA C4 WB1 C3 C6 C9 WB2 C10 L2 C14 C11 C12 C13 900 MHz Rev 02 Figure 3. 930-960 MHz Broadband Test Circuit Component Layout (MRF9030MBR1) MRF9030MR1 MRF9030MBR1 4 MOTOROLA RF DEVICE DATA TYPICAL CHARACTERISTICS h , DRAIN EFFICIENCY (%) IMD, INTERMODULATION DISTORTION (dBc) -10 -12 -14 -16 -18 22 21 G ps , POWER GAIN (dB) 20 19 18 17 16 15 14 930 935 940 IRL VDD = 26 Vdc Pout = 30 W (PEP) IDQ = 250 mA Two-Tone, 100 kHz Tone Spacing 945 950 955 f, FREQUENCY (MHz) IMD Gps 50 45 40 35 -30 -32 -34 -36 -38 960 Figure 4. Class AB Broadband Circuit Performance IMD, INTERMODULATION DISTORTION (dBc) 21.5 21 G ps , POWER GAIN (dB) 20.5 20 300 mA 250 mA 200 mA VDD = 26 Vdc f1 = 945 MHz f2 = 945.1 MHz 1 10 100 -15 -20 -25 -30 -35 -40 -45 -50 -55 250 mA 0.1 1 IDQ = 200 mA 300 mA VDD = 26 Vdc 375 mA f1 = 945 MHz f2 = 945.1 MHz 10 100 IDQ = 375 mA 19.5 19 18.5 0.1 Pout, OUTPUT POWER (WATTS) PEP Pout, OUTPUT POWER (WATTS) PEP Figure 5. Power Gain versus Output Power Figure 6. Intermodulation Distortion versus Output Power IMD, INTERMODULATION DISTORTION (dBc) -10 -20 -30 -40 -50 -60 -70 -80 0.1 G ps , POWER GAIN (dB) 3rd Order 18 16 14 12 10 0.1 1 10 VDD = 26 Vdc IDQ = 250 mA f = 945 MHz 40 30 20 10 0 100 5th Order 7th Order 1 10 100 Pout, OUTPUT POWER (WATTS) PEP Pout, OUTPUT POWER (WATTS) AVG. Figure 7. Intermodulation Distortion Products versus Output Power Figure 8. Power Gain and Efficiency versus Output Power MOTOROLA RF DEVICE DATA MRF9030MR1 MRF9030MBR1 5 , DRAIN EFFICIENCY (%) VDD = 26 Vdc IDQ = 250 mA f1 = 945 MHz f2 = 945.1 MHz 22 20 Gps IRL, INPUT RETURN LOSS (dB) 60 50 20 G ps , POWER GAIN (dB) 18 Gps 40 20 0 -20 -40 -60 100 16 14 12 10 0.1 IMD 1 10 VDD = 26 Vdc IDQ = 250 mA f1 = 945 MHz f2 = 945.1 MHz Pout, OUTPUT POWER (WATTS) PEP Figure 9. Power Gain, Efficiency and IMD versus Output Power MRF9030MR1 MRF9030MBR1 6 , DRAIN EFFICIENCY (%) IMD, INTERMODULATION DISTORTION (dBc) 22 60 MOTOROLA RF DEVICE DATA Zo = 5 f = 930 MHz f = 930 MHz Zin f = 960 MHz f = 960 MHz ZOL* VDD = 26 V, IDQ = 250 mA, Pout = 30 Watts (PEP) f MHz 930 945 960 Zin Zin 1.07 - j0.160 1.14 - j0.385 1.17 - j0.170 ZOL* 3.53 + j0.20 3.41 + j0.24 3.60 + j0.17 = Complex conjugate of source impedance. ZOL* = Complex conjugate of the optimum load impedance at a given output power, voltage, IMD, bias current and frequency. Note: ZOL* was chosen based on tradeoffs between gain, output power, drain efficiency and intermodulation distortion. Input Matching Network Device Under Test Output Matching Network Z in Z * OL Figure 10. Series Equivalent Input and Output Impedance (MRF9030MR1) MOTOROLA RF DEVICE DATA MRF9030MR1 MRF9030MBR1 7 Zo = 5 Zin f = 930 MHz f = 960 MHz ZOL* f = 960 MHz f = 930 MHz VDD = 26 V, IDQ = 250 mA, Pout = 30 Watts (PEP) f MHz 930 945 960 Zin Zin 1.0 + j0.18 1.0 + j0.10 1.0 + j0.03 ZOL* 3.05 + j0.09 3.00 + j0.07 2.95 + j0.03 = Complex conjugate of source impedance. ZOL* = Complex conjugate of the optimum load impedance at a given output power, voltage, IMD, bias current and frequency. Note: ZOL* was chosen based on tradeoffs between gain, output power, drain efficiency and intermodulation distortion. Input Matching Network Device Under Test Output Matching Network Z in Z * OL Figure 11. Series Equivalent Input and Output Impedance (MRF9030MBR1) MRF9030MR1 MRF9030MBR1 8 MOTOROLA RF DEVICE DATA NOTES MOTOROLA RF DEVICE DATA MRF9030MR1 MRF9030MBR1 9 PACKAGE DIMENSIONS B E1 2X 2X D3 E4 aaa M PIN ONE ID DA NOTES: 1. CONTROLLING DIMENSION: INCH. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M-1994. 3. DATUM PLANE -H- IS LOCATED AT TOP OF LEAD AND IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE PLASTIC BODY AT THE TOP OF THE PARTING LINE. 4. DIMENSIONS "D1" AND "E1" DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS .006 PER SIDE. DIMENSIONS "D1" AND "E1" DO INCLUDE MOLD MISMATCH AND ARE DETER MINED AT DATUM PLANE -H-. 5. DIMENSION b1 DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE .005 TOTAL IN EXCESS OF THE b1 DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. DATUMS -A- AND -B- TO BE DETERMINED AT DATUM PLANE -H-. 7. DIMENSION A2 APPLIES WITHIN ZONE "J" ONLY. 8. DIMENSIONS "D" AND "E2" DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS .003 PER SIDE. DIMENSIONS "D" AND "E2" DO INCLUDE MOLD MISMATCH AND ARE DETER MINED AT DATUM PLANE -D-. DIM A A1 A2 D D1 D2 D3 E E1 E2 E3 E4 F b1 c1 aaa INCHES MIN MAX .076 .084 .038 .044 .040 .042 .416 .424 .376 .384 .290 .320 .016 .024 .436 .444 .236 .244 .066 .074 .150 .180 .058 .066 .025 BSC .193 .199 .007 .011 .004 MILLIMETERS MIN MAX 1.93 2.13 0.96 1.12 1.02 1.07 10.57 10.77 9.55 9.75 7.37 8.13 0.41 0.61 11.07 11.28 5.99 6.20 1.68 1.88 3.81 4.57 1.47 1.68 0.64 BSC 4.90 5.06 0.18 0.28 0.10 D aaa M DA 2X b1 D1 E A PIN 2 D2 PIN 3 c1 H A1 DATUM PLANE A2 NOTE 7 F ZONE J MRF9030MR1 MRF9030MBR1 10 CCCC CCCC CCCC CCCC CCCC CCCC CCCC CCCC CCCC BOTTOM VIEW 2X E3 EXPOSED HEATSINK AREA PIN 1 A STYLE 1: PIN 1. DRAIN 2. GATE 3. SOURCE E2 D CASE 1265-07 ISSUE F (TO-270) PLASTIC (MRF9030MR1) MOTOROLA RF DEVICE DATA B 2X E1 A r1 B M aaa M CA M PIN 3 PIN ONE ID D1 2X b1 M aaa CA M D 2 1 PIN ONE ID E VIEW Y-Y NOTES: 1. CONTROLLING DIMENSION: INCH. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DATUM PLANE -H- IS LOCATED AT THE TOP OF LEAD AND IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE PLASTIC BODY AT THE TOP OF THE PARTING LINE. 4. DIMENSIONS "D" AND "E1" DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS .006 PER SIDE. DIMENSIONS "D" AND "E1" DO INCLUDE MOLD MISMATCH AND ARE DETERMINED AT DATUM PLANE -H-. 5. DIMENSION "b1" DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE .005 TOTAL IN EXCESS OF THE "b1" DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. DATUMS -A- AND -B- TO BE DETERMINED AT DATUM PLANE -H-. 7. DIMENSION A2 APPLIES WITHIN ZONE "J" ONLY. DIM A A1 A2 D D1 E E1 F b1 c1 r1 aaa INCHES MIN MAX .098 .110 .038 .044 .040 .042 .926 .934 .810 BSC .438 .442 .246 .254 .025 BSC .199 .193 .007 .011 .063 .068 .004 MILLIMETERS MIN MAX 2.49 2.79 0.96 1.12 1.02 1.07 23.52 23.72 20.57 BSC 11.12 11.23 6.25 6.45 0.64 BSC 4.90 5.05 .18 .28 1.60 1.73 .10 c1 H DATUM PLANE A A1 A2 7 F ZONE "J" SEATING PLANE Y Y C STYLE 1: PIN 1. DRAIN 2. GATE 3. SOURCE CASE 1337-01 ISSUE O (TO-272 DUAL LEAD) PLASTIC (MRF9030MBR1) MOTOROLA RF DEVICE DATA MRF9030MR1 MRF9030MBR1 11 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. MOTOROLA and the logo are registered in the US Patent & Trademark Office. All other product or service names are the property of their respective owners. E Motorola, Inc. 2002. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1-303-675-2140 or 1-800-441-2447 JAPAN: Motorola Japan Ltd.; SPS, Technical Information Center, 3-20-1, Minami-Azabu. Minato-ku, Tokyo 106-8573 Japan. 81-3-3440-3569 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Centre, 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong. 852-26668334 Technical Information Center: 1-800-521-6274 HOME PAGE: http://www.motorola.com/semiconductors/ MRF9030MR1 MRF9030MBR1 12 MOTOROLA RF DEVICEMRF9030M/D DATA |
Price & Availability of MRF9030MBR1
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |